Clarification from the agency

Restricted to current members of the Iowa Army National Guard.

As a ELECTRONICS MECHANIC, WG-2604-11 your duties are below.

1. Performs functional tests, analyzes performance and malfunctions, removes, installs, tests, maintains, modifies, performs alignments and troubleshoots the electronic, electrical, mechanical and hydraulic assemblies, modules, and interconnecting cables of a variety of combat and tactical equipment to include the M1 series main battle tank, M2/3 series Bradley fighting vehicle, Multiple Launch Rocket System (MLRS), TOW Missile System and the ATACMS Launch Loader Module (LLM). Utilizes Integrated Family Test Equipment (IFTE), Built In Test Equipment (BITE) and break out boxes (BOB) for fault isolation, verification, or adjustment of assemblies and modules. Repairs or replaces chassis mounted components on Unit Under Test (UUT). Performs Automatic Test Equipment (ATE) operations for fault isolation on LLM electronic modules, circuit cards, and assemblies to component level. Replaces faulty components on UUT printed circuit boards and power distribution systems. Utilizes oscilloscopes, signal generators, digital multi-meters, and other test equipment to locate, diagnose, and repair malfunctions.
2. Troubleshoots and repairs launch pod/container (LP/C), trainer rocket simulator modules, Missiles/Launchers Pod Assembly (M/LPA), trainer missile simulator modules, and various like items. Troubleshoots carrier electrical and power distributions systems as an integrated subsystem of the weapon system or equipment being repaired. Isolates faulty assemblies, cables, wiring harnesses and modules to component level for repair or replacement. Insures proper integration of information between carrier, Fire Control System (FCS), vehicle and equipment hydraulic and mechanical systems, secure digital communications system, and intercommunications system. Installs equipment modifications to system per technical work orders. Performs initial and final checks and may perform inspections when required of designated systems. May act as quality assurance/control inspector for other mechanics' work. Determines deficiencies in troubleshooting procedures for the equipment being repaired and makes recommendations for corrective action to technical manuals.
3. Performs field and limited sustainment maintenance to include installation, routine maintenance, repair, and overhaul of fixed and mobile operational communication and electronics systems, e.g., shelter mounted AM radio and teletype systems, shelter mounted single side band radio and teletype systems, shelter mounted radio relay and terminal systems, complex radar systems, interrogators, gun, rocket, and missile fire control, directional and digital computer systems, peripheral equipment, and related test equipment, and Modification Table Of Equipment (MTOE) authorized automation equipment. Repairs, aligns, and adjusts missile guidance control systems, infrared night vision sights, optical sights, and traversing units. Removes and replaces defective electrical, electronic, and mechanical components. Conducts inspections, diagnoses nature and extent of equipment malfunction. Determines whether equipment may be economically repaired or declared unserviceable, and performs required maintenance to restore to a serviceable condition various types of tactical computers, radio sets, and similar items. Repairs or salvages defective components. Isolates and diagnoses cause of circuit/component malfunction using signal string lists, schematics, standard, special, and electronic Test Measurement and Diagnostic Equipment (TMDE) or repair equipment. Uses associated field maintenance equipment in analytical maintenance procedures. Interprets complex schematic diagrams. Must exercise a high degree of judgment regarding methods and procedures for completing assignments, which may involve extending the use of conventional tools and equipment and improving changes to techniques, and procedures to reach specified parameters when factors such as temperature extremes, aging of equipment, or modification of circuits have changed operating conditions. Installs and applies equipment modifications when directed.
4. Uses various types of test equipment to include systems test sets and stands such as AN/GRM-122s, frequency meters, standing wave indicators, oscillators, ohmmeters, voltmeters, resistance bridges, and signal generators to localize trouble by component unit, by circuit within a component, and by element of a circuit. Uses special and common hand tools, power tools, and gauges to make intricate repairs. Fabricates items and parts for repair of mechanical and electronic equipment.
5. Performs administrative functions in establishing and maintaining maintenance records on equipment maintained or repaired. Assists in the preparation of requests for required repair parts.
6. Performs other duties as assigned. D1205

Conditions of employment

NATIONAL GUARD MEMBERSHIP IS REQUIRED: This is an excepted position that requires military membership in a compatible military assignment in the Iowa Army National Guard. Selectee will be required to wear the military uniform. Acceptance of this excepted position constitutes concurrence with these requirements as a condition of employment.

APPLICATION MATERIALS MUST BE RECEIVED BY 07/21/2026 . FAILURE TO PROVIDE COMPLETE INFORMATION MAY RESULT IN YOUR NOT RECEIVING CONSIDERATION FOR THIS POSITION. Please refer to the Qualifications and Evaluations Section of this Announcement to understand the qualification requirements, and the How to Apply Section for detailed instruction on applying.

TRIAL PERIOD REQUIREMENT: As a condition of employment for accepting this position, you will be required to serve a 2-year trial period or 1-year (Veterans Preference Eligibles Only) during which we will evaluate your fitness and whether your continued employment advances the public interest. In determining if your employment advances the public interest, we may consider:

• Your performance and conduct.
• The needs and interests of the agency.
• Whether your continued employment would advance organizational goals of the agency or the Government; and
• Whether your continued employment would advance the efficiency of the Federal service.

Upon completion of your trial period your employment will be terminated unless you receive certification, in writing, that your continued employment advances the public interest.

SECURITY CLEARANCE REQUIREMENT: Employment is subject to attaining and maintaining a clearance as required by this position. If the selectee does not possess the applicable security clearance when hired, application must be made within 30 days of the start date. Failure to make application for the required security clearance will result in termination of employment.

Failure to complete prescribed courses may be cause for reassignment or termination of FTS.

Military Rank Requirements: Military Rank Requirements: Warrant Officer and Enlisted (WO1 and below)

Qualifications

In describing your experience, please be clear and specific. We will not make assumptions regarding your experience. Applicants who do not fully address the minimum/specialized experience needed for the position in their resume will not be referred for consideration. Your resume must contain your own words. Resumes that are verbatim, from this announcement, any PD's, or any other applicants will not be considered.

MINIMUM REQUIREMENTS: Experience or training which demonstrates the applicant's knowledge of electrical or electronic theory, knowledge of common testing procedures, skill in the use of hand tools of the electronics trade, and skill in reading schematics.

SPECIALIZED EXPERIENCE REQUIREMENTS: WG-2604-11: Must haveexperience in the following:

• Experience or training in utilizing principles, basic functions, and application of theory of electronic systems or equipment.
• Experience in diagnosing problems and determining needed repairs for malfunctions in electronic equipment or systems.
• Experience in making mechanical repairs that required the use of precision measuring and calibrating equipment.
• Experience in using complex test equipment such as deviation meters, complex special test panels, etc.
• Experience which demonstrates the ability to interpret technical manuals, specifications, and publications.

How you will be evaluated

You will be evaluated for this job based on how well you meet the qualifications above.

Once the announcement has closed, your resume and supporting documentation will be used to determine if you meet the qualifications listed on this announcement. If you are found to be among the qualified candidates, you will be referred to the selecting official for employment consideration.

Verbiage displayed on your resume or application must contain your own words. You may refer to position descriptions, i.e. the general and specialized experience located within the vacancy announcement, to assist with describing work experiences; however, resumes or applications received in verbatim will not be considered. In your resume you will need to address the general and specialized experience listed above. Please use as much detail as needed, giving dates (months and years) of the experience, position title and how the experience was gained. This information is needed to determine if you are qualified for the position.

Knowledge, Skills and Abilities required for this position:

1. Comprehensive knowledge of operating electronic principles such as circuit elements, digital logic, microprocessors, core memory, interface circuits, digital data transmission, microwave, antennas, signal behavior, amplification, and display.
2. Ability to troubleshoot, install, repair, and maintain complex electronic systems where circuit theory must be used to understand the operation of individual circuits. Skill in developing new test and repair procedures for which none exist, and when possible, improving existing procedures.
3. Ability to understand the interaction of a number of complex, interrelated circuits to determine the cause of a malfunction and the interaction of various factors.
4. Extensive knowledge of electromechanical servo systems, pneumatics, hydraulics, and mechanical and electric motor systems and their effect on each other.
5. Skill in interpreting complex drawings, specifications, and schematics of complete systems to recognize the function and interconnections of the various assemblies and troubleshoot the systems from schematic, following signal paths through a complex path of interconnections of components, assemblies, subassemblies, and connecting cable harnesses.
6. Knowledge and skill to modify systems by adding, altering, or removing components in order to standardize or alter the purpose of the equipment or to incorporate new features developed since the equipment was manufactured.
7. Skill in using a wide variety of electronic test equipment such as systems test sets, frequency meters, standing wave indicators, oscillators, ohmmeters, voltmeters, resistance bridges, and signal generators, and the use of special and common hand tools, power tools, and gauges. Skill in applying this knowledge to adapt test procedures to available test equipment, to develop time efficient means to return equipment to operation.
8. Skill in using gunner's quadrants, transits, levels, and theodolites to survey LP/C, M/LPA mounts, and SRP/PDS mounting bolts for exactness. Skill to use recovery-rigging techniques to attach/secure hoists, slings, and lifting devices using authorized equipment to accomplish repairs.
9. Ability to switch from one theory of operations to another or to combine theories depending on the type of system being repaired.
10. Skill and knowledge to provide technical assistance and instruction.