Clarification from the agency

In order to be eligible for this position you must currently be an Enlisted Member (E3/A1C - E5/SSgt) currently employed (permanent) in the Virginia Air National Guard Technician Program.

As a Composite Fabricator (Title 32), WG-4352-10, you will perform the below duties:

1. Improves, modifies, fabricates, and designs repairs for low observable assemblies, sub-assemblies, and components ensuring proper weight to strength ratios are met and maintains structural and low observable integrity requirements including associated aircraft structural composites. Removes, inspects, designs, and implements emergency repairs using various novel techniques or methods. Documents maintenance actions in applicable automated system and/or records. Advises and provides documents to associated engineers, overhauls, reinstalls, or adjusts irregular surfaces, control system components, assemblies/sub-assemblies, and specialized coatings. Identifies and discusses potential problems in new designs or maintenance methods and procedures with engineers and other originators, advises on improvements in repair and maintenance methods including application techniques. May attend meetings or working groups with engineers, contractors etc. to resolve problems and maintain awareness of current techniques and processes that may not be documented. Orders and turns in aircraft parts and assemblies. May serve as the primary worker responsible for monitoring the completion of assigned maintenance tasks.
2. Performs a variety of extensive evaluations of weapons systems using a variety of complex tools and assessment equipment to assess that the proper radar cross section (RCS) signature according to the associated technical order data, mission requirements and other policy regulations, instructions, and guidance. Inspections will be done on weapons system structure, LO coating, and LO materials. Evaluates operational deficiencies and records LO system damage types, specific multi-complex dimensions, and location plots using the automated maintenance systems related to the specific weapons system. Records RCS results and updates aircraft signature status following aircraft flights, at scheduled intervals, and/or after LO coating/structural maintenance and repair actions. Conducts audits of LO aircraft and associated signature management databases, ensuring that RCS signature reported accurately reflects aircraft physical status. Certifies integrity of signature management databases through verification, addition, and removal of audit data. Audits of weapons systems will be conducted utilizing applicable portable automated electronic devices to mark and record signature assessment damages.
3. Performs repair, application, and maintenance of corrosion preventatives and paints on aircraft, powered, and non-powered AGE (aerospace ground equipment). Identifies metal corrosion. Performs necessary testing to identify type of corrosion present by examination with magnifying equipment, chemical and mechanical methods. Treats aircraft engines in accordance with applicable technical publications. Identifies, blends, stores, controls, and disposes of hazardous materials such as acids, caustics, alcohols, solvents, cleaners, primers and surface coatings used for corrosion removal, treatment and protection in accordance with applicable directives. Removes corrosion by mechanical and chemical procedures to include use of portable powered (electric and pneumatic) sanders, buffers, brushes, bead blasters, vacuum cleaners, scrapers, grinders, acids, caustics, solvents, alcohols and other agents used in corrosion control processes. Treats metal with chemical procedures, such as pretreatments, to protect metal from oxidation. Performs functions such as pickling of metals to prepare for good bonding with primer coat of protective materials. Applies protective coatings, markings, and decals. Use conventional paint spray equipment, electrostatic spray equipment, brushes and special applicators when applying primers and surface coatings. Operates wash rack as required. Accomplishes corrosion and washing inspections within schedule provided to ensure compliance with monthly and weekly maintenance plan. Assesses corrosion problems and select appropriate treatment to correct problems and minimize future repair work for same or related problem area. Conducts training on proper methods and procedures of composite wash rack operations.
4. Collects, compiles, and records LO systems data for maintenance scheduling, statistical analysis, trending, and historical record. Performs data searches and reports findings as directed. Manages an array of related databases and spreadsheets to capture and catalog data elements for trending, information sharing working groups, and benchmarking. Responsible for documenting, obtaining, applying, securing, and protecting classified records, documents, hardware and software. Analyzes trends in deficiencies, provides engineers and other entities with devised repair procedures, performs prototype repair while providing instructions to other employees
5. Performs other duties as assigned.

Conditions of employment

• NATIONAL GUARD MEMBERSHIP IS REQUIRED. If you are not sure you are eligible for military membership, please contact a National Guard recruiter prior to applying for this position.
• This is an excepted service position that requires membership in a compatible military assignment in the employing state's National Guard, required prior to the effective date of placement.
• Selectee will be required to wear the military uniform.
• Acceptance of an excepted service position constitutes concurrence with these requirements as a condition of employment.
• Applicants who are not currently a member of the National Guard must be eligible for immediate membership and employment in the National Guard in the military grade listed in this announcement.
• Males born after 31 December 1959 must be registered for Selective Service.
• Federal employment suitability as determined by a background investigation.
• May be required to successfully complete a trial period.
• Participation in direct deposit is mandatory.
• This position is not located at a bargaining unit.
• All job seekers will be required to limit their resumes to 2 pages in length when applying for job opportunity announcements (JOAs).

Qualifications

NOTE: Qualifications are based on breadth/level of experience. In addition to describing duties performed, applicants must provide the exact date of each period of employment (from MM/DD/YY to MM/DD/YY) add the number of hours worked per week if part time. As qualifications determinations cannot be made when resumes do not include the required information, failure to provide this information may result in disqualification. Applicants are encouraged to use the USAJOBS Resume Builder to develop their federal resume.

NOTE: All job seekers will be required to limit their resumes to 2 pages in length when applying for job opportunity announcements (JOAs).

WHO CAN APPLY:
GROUP I - All qualified Male/Female Enlisted Personnel (E3/A1C - E5/SSgt) currently employed (permanent) in the Virginia Air National Guard Military Technician Program.

Military Grades: Enlisted Personnel (E3/A1C - E5/SSgt)

GENERAL EXPERIENCE: Applicant must have experience or knowledge of skill in the use of basic hand and powered tools common to the bonding operations as well as those utilized in the sheet metal trade.

SPECIALIZED EXPERIENCE: Applicant must have at least 18 months of specialized experience, equivalent to at least the WG-8 level, or equivalent pay band in other pay systems in the Federal government? This experience may also have been obtained in the private sector but must demonstrate that it is comparable to the WG grade indicated. This experience must include activities such as:

1. Experience or training demonstrating a practical thorough knowledge of the newest substances to recommend and/or select materials for prototype and one-time items.
2. Have an extensive knowledge of the properties and machining characteristics of a variety of composite or plastic materials.
3. Experience or knowledge in establishing manufacturing procedures for newly developed compound materials by experimenting with various manufacturing techniques, curing times, irregular curvatures (surfaces), temperatures, and pressure. Knowledge in manufacturing master patterns and molds with numerous compound curves and intersecting compound angles.
4. Experience or knowledge in applying mathematics to calculate loads, fits, sizes, and weights not provided in instructions and blueprints to overcome design flaws and lay out more complex items.

How you will be evaluated

You will be evaluated for this job based on how well you meet the qualifications above.

Once the announcement has closed, your resume and supporting documentation will be used to determine if you meet the qualifications listed on this announcement. If you are minimally qualified, your resume and supporting documentation will be compared to your responses on the assessment questionnaire to determine your level of experience. If you rate yourself higher than is supported by your application package, your responses may be adjusted and/or you may be excluded from consideration for this position. If you are found to be among the top qualified candidates, you will be referred to the selecting official for employment consideration.

Your qualifications will be evaluated on the following competencies (knowledge, skills, abilities and other characteristics):