Clarification from the agency

This position has a limited area of consideration to Command-wide (AETC).

• Performs all phases of liquid fuels and water systems component maintenance including inspections, tests, preventive maintenance, troubleshooting, repair and system modifications.
• Inspects and tests electrical components in liquid fuel receiving, storage, and distribution facilities and performs preventive maintenance on these components. Participates in cleaning and inspection of the interior surface of bulk storage tanks for fuel and water systems, to include above and below ground, by entering tanks.
• Independently installs, modifies, repairs, and maintains a variety of new and existing utility, supply, and disposal systems and equipment such as sewage, water, oil, and gas distribution systems, and water closets, tubs, backflow prevention devices/assemblies, fire sprinkler systems, and showers. Assembles, installs and repairs pipes, fittings and fixtures of heating, water, and drainage systems, according to specifications and plumbing codes.
• Uses and maintains tools such as, multi-meters, flange spreaders, motor joists/lifts, hydraulic jacks, impact wrenches, pneumatic tools, air compressors, torque wrenches, prover tanks, portable electrical and air driven pumps, tubing benders, tapes, rules, plumb bobs, hand and power pipe threaders, cutters, pipe wrenches, angle drills, hacksaws and power saws, power sewer cleaning equipment, various combustible gas and toxic vapor detectors and meters, self contained breathing apparatus, supplied air respirators, and various personnel protective equipment.
• Utilizes safe work practices and procedures following established safety rules and regulations and maintains a safe and clean work environment.

Conditions of employment

• U.S. Citizenship Required
• Males must be registered for Selective Service, see www.sss.gov
• This position is subject to provisions of the DoD Priority Placement Program
• Disclosure of Political Appointments
• Shift work may be required
• The employee may be required to work other than normal duty hours, which may include evenings, weekends, and/or holidays
• The work may require that the employee be certified in the use of a respirator
• The work may require that the employee be certified or able to be certified as qualified for entry into hazardous liquid fuel tanks for inspection, cleaning, and repair
• The work may require the employee to drive a motor vehicle. An appropriate, valid driver's license may be required for the position
• A pre-employment physical is required. Position requires the ability to discern colors, contrast, and depth
• In accordance with Federal law, incumbent will be required to obtain and maintain an American Backflow Prevention license, or equivalent
• Must be able to obtain and maintain an appropriate security clearance
• This position has a limited area of consideration to Command-wide (AETC).

Qualifications

In order to qualify, you must meet the quality level of experience requirements described in the Office of Personnel Management (OPM) Qualification Standards Handbook X-118C.

QUALIFICATIONS: Applicants will be rated in accordance with the OPM Qualification Standard Handbook X-118C for the WG-4200, Plumbing and Pipefitting Group. Although a specific length of time and experience is not required for most blue-collar positions, you must meet any screen-out element listed, and show through experience and training that you possess the quality level of knowledge and skill necessary to perform the duties of the position at the level for which you are applying. Qualification requirements emphasis is on the quality of experience, not necessarily the length of time.

The screen out element for this position is ability to do the work of a WG-4255 FUEL DISTRIBUTION SYSTEM MECHANIC without more than normal supervision.

JOB ELEMENTS: Your qualifications will be evaluated on the basis of your level of knowledge, skills, abilities and/or competencies in the following areas:

1. Knowledge of fuel/utility distribution and storage systems and of the physical properties and hazards associated with the handling of various types of petroleum fuels. Knowledge of preventive maintenance and inspection techniques as applied to fuel distribution, storage and utility systems. Knowledge of safety, environmental and security regulations, procedures, and practices.
2. Skill in calibration of fuel dispensing/metering devices and pressure gauges. Skill in installing, modifying, and repairing new and existing utility, supply, and disposal systems and equipment without more than normal supervision. Skill in techniques used to measure, cut, thread, join, and fit piping and tubing.
3. Ability to analyze deficiencies and diagnose malfunctions of system components such as automatic control valves, pumps, flow meters, etc.
4. Knowledge of troubleshooting, maintenance, and repair of electrical components such as electric motors, disconnect switches, starters, contactors, solenoids, and magnetic switches
5. Knowledge of technical practices in order to plan, lay out, install modify, troubleshoot and repair various systems and equipment.
6. Skill in using and maintaining tools and equipment such as levels, plumb bobs, various gages and meters, hydrostatic pumps, power tools, pressure testing tools and equipment, electrical test and measuring equipment, combustible and toxic gas indicators.

PHYSICAL EFFORT: Performs work which involves frequent bending, reaching, crouching, kneeling, crawling, stooping, standing, arm movement, and climbing. Sometimes must work in awkward, tiring, or uncomfortable positions, or cramped areas. Frequently lifts, carries, and sets up parts and equipment weighing up to 50 pounds and occasionally lifts items weighing over 50 pounds using jacks, hoists, or helpers. May be required to make repairs and installations from ladders, scaffolding, and platforms and to enter bulk storage tanks through tank manholes 24 inches in diameter.

WORKING CONDITIONS: Work is performed inside and outside and may be subject to extreme heat and cold and hard, damp floors or surfaces. Work is usually dirty, dusty, and greasy. May be required to make installations and repairs outside during inclement weather. Frequently exposed to the possibility of cuts, scrapes, strains, bruises, burns, infections, and skin abrasions. Subject to skin irritation from fuels and oils; exposure to noxious fumes or toxic vapors; and danger of fire, explosion, electrical shock, and asphyxiation. Occasionally exposed to the possibility of broken bones. May be subject to claustrophobic conditions and the wearing of cumbersome breathing equipment when performing periodic cleaning of the interior of bulk storage tanks. Works around machinery or moving parts. May wear and use uncomfortable protective clothing and safety devices such as protective eyeglasses, ear devices, hard hats, hard-toe shoes, respirators, and gloves for long periods of time.

PART-TIME OR UNPAID EXPERIENCE: Credit will be given for appropriate unpaid and or part-time work. You must clearly identify the duties and responsibilities in each position held and the total number of hours per week.

VOLUNTEER WORK EXPERIENCE: Refers to paid and unpaid experience, including volunteer work done through National Service Programs (i.e., Peace Corps, AmeriCorps) and other organizations (e.g., professional; philanthropic; religious; spiritual; community; student and social). Volunteer work helps build critical competencies, knowledge and skills that can provide valuable training and experience that translates directly to paid employment. You will receive credit for all qualifying experience, including volunteer experience.

How you will be evaluated

You will be evaluated for this job based on how well you meet the qualifications above.

Your application package (resume, supporting documents, and responses to the questionnaire) will be used to determine your eligibility, qualifications, and quality ranking for this position. Please follow all instructions carefully. Errors or omissions may affect your rating or consideration for employment.

BASIS OF RATING: Your application will be rated under the Cut Point procedures based on the extent to which the quality, depth, and complexity of your experience relates to the qualification requirements. Additional points are not added for Veteran's Preference; however, Veteran's Preference is considered where applicable.

Best Qualified Group: Candidates in this category possess exceptional skills and experience to exceed well above the minimum requirements.
Fully Qualified Group: Candidates in this category possess good skills and experience above the minimum requirements.
Basically Qualified Group: Candidates in this category meet the minimum experience requirements.

The resume/documents you submit must support your responses to the online questionnaire. If your application contradicts or does not support your questionnaire responses, you will receive a rating of "not qualified" or "insufficient information" and you will not receive further consideration for this job.

Applicants who disqualify themselves will not be evaluated further.

APPRAISALS/AWARDS: Hiring Managers use objective methods and consider previous performance appraisals and awards in the selection process. Current Federal Civilian employees should list any relevant performance related rating and/or awards in your resume.